Indmar

Indmar Knock Sensor Genuine Indmar knock sensor. This part is commonly found in Indmar engines in MasterCraft, Malibu, Supra and Moomba boats. This part threads into the block and features a wire...

Indmar LT-1 & LTR Water Pump Fits Indmar LT1 Corvette and LTR engines used in MasterCraft boats. Johnson crankshaft mounted pump. New pump.Note: Early '93 and some '94 LT1 engines used threaded...

Indmar Ford Oil Filter for 2015 Raptor 6.2 Engines Only Fits all Indmar Ford Raptor 6.2L based marine engines for the 2015 model year only. Marine engines should get an oil and filter change every...

Get the spark your engine needs with a new spark plug wire set from MasterCraft. This wire set fits these 2005 and older 5.7L Engines - MCX, RTP-1, and Predator. Please note: No returns will be...

Indmar Water Pump Impeller This kit fits almost all Indmar marine engines (Malibu, Supra, Moomba, etc.) and almost every MasterCraft produced from 1987 until the change to Ilmor engines in 2011...

Indmar Raw Water Pump Fits Indmar Ford and GM engines like std and HO 351, TBI, MCX, RTP, Predetor, LQ9, LY6, 8.1. Johnson crankshaft mounted pump. New pump.Please note this pump DOES NOT FIT LT1...

Indmar Thermostat Gasket This thermostat gasket is commonly used on Indmar 350 block engines including the RTP-1, MCX, Assault and many others. This is a 2 bolt gasket used on the top half of the...

Indmar LT1 Thermostat Gasket This thermostat gasket is used on the Indmar LT-1 Corvette engines which were optional in MasterCraft boats from 1993 to 1999. It is used to seal the 160 degree drilled...

Indmar 160 Degree Thermostat Indmar 160-degree thermostat. Use the boat part look up below to ensure you are purchasing the correct part for your boat.  

Indmar Thermostat Gasket This thermostat gasket is commonly used on many late 80's to early 90's Indmar engines. This gasket measures 3 38/" across (at the widest point) and 4 1/4" long. This part...

Rotor (86-Older) Prestolite Fits Ford and GM based V8 engines 1986 and older with a Prestolite distributor. Rotor only.Note: There were a FEW 1987 boats built that had the "old" CLIP-ON type...

Indmar 160 Degree Thermostat Drilled Indmar 160 degree thermostat for Corvette LT-1 engines used in MasterCraft boats from 1993 to 1999. This thermostat features two small holes that are drilled...

Indmar Thermostat Gasket This thermostat gasket is commonly used on Indmar 350 block engines including the RTP-1, MCX, Assault and many others. This is a 3 bolt gasket used on the bottom half of the...

Indmar Spark Plug Wire Set | 755007 Get the spark your engine needs with new spark plug wire set. Fits Ford 351w, 302(5.8, 5.0), based small blocks with either a Prestolite or a Mallory distributor...

Prestolite Distributor Rotor (1987 & newer) Fits Ford and GM based V8 engines 1987 and newer with a Prestolite distributor. This is the Rotor only. These engines were used by MasterCraft,...

Indmar Oil Pressure Sender Genuine Indmar Oil Pressure Sender. This part is commonly found in Indmar engines in MasterCraft, Malibu, Supra and Moomba boats. Use the boat part look up below to...

Indmar Oil Cap Proper maintenance ensures that your boat performs in peak condition year after year. Indmar Engines offers this replacement oil cap for engines using steel valve covers and a...

Johnson Raw Water Cover Plate Screw The Johnson Raw Water Cover Plate Screw fits almost all Indmar marine engines (Malibu, Supra, Moomba, etc.) and almost every MasterCraft produced from 1987 until...

Johnson Raw Water Pump Cover Plate The Johnson Raw Water Pump Cover Plate fits almost all Indmar marine engines (Malibu, Supra, Moomba, etc.) and almost every MasterCraft produced from 1987 until...

Ford Oil Filter for Indmar & PCM Fits all Ford based 351 & 302 (5.8 & 5.0) engines. Marine engines should get an oil and filter change every 50 hours of run time. Keep your Ford based...