Engine Parts

Ilmor Manifold Air Temp Sensor (MAT Sensor)| MV8V-1052 Ilmor MAT Sensor for MasterCraft boats. Specifically designed by Ilmor and MasterCraft for 5.7L 6.0L 6.2L Ilmor engines.  Tisi part cannot be returned if it is removed from the plastic bag it is...

MasterCraft Fuel Line Disconnect Tool The Fuel Line Disconnect Tool is an essential part of removing fuel lines from a MasterCraft Fuel Pump!This tool makes quick work of removing the fuel lines from your in tank fuel pump. Removing the fuel line(s) is...

Prestolite Points Fits all Ford and GM based V8 engines using a Prestolite points distributor. This is the Points only, tune up kits are available for these boat engines as well. These engines were used by MasterCraft, Supra, and Nautique.Please note: No...

Ilmor Engine Temperature Sensor | MV8V-1190 Ilmor water temperature sensors are engineered for precision and durability and the highest signal accuracy. Ilmor Engine Temp Sensor for MasterCraft boats. Specifically designed by Ilmor and MasterCraft for...

Indmar Thermostat Gasket This thermostat gasket is commonly used on Indmar 350 block engines including the RTP-1, MCX, Assault and many others. This is a 3 bolt gasket used on the bottom half of the thermostat housing where it meets the intake manifold...

Ilmor Thermostat Housing O-Ring The Ilmor remote thermostat housing mounting o-ring offers application-specific materials to give you a sealing solution with the performance and durability you can trust. This Thermostat Housing O-Ring is used with both...

Ilmor O2 Sensor Upstream | MV8V-1017 Ilmor specified oxygen sensor is the recommended replacement for your Ilmor engine. The sensors provide special feedback to your engine’s exhaust system by measuring the proportion of oxygen in the exhaust gases...

Circulating Water Pump for Indmar & PCM Ford Engines Fits all Ford based engines from Indmar, PCM, as well as others.  This new bi-rotational pump comes with a new mounting gasket to ensure a proper fit on your Ford 302 or 351 boat motor...

Ilmor O2 Sensor Downstream | MV8V-1018 Ilmor specified oxygen sensor is the recommended replacement for your Ilmor engine. The sensors provide special feedback to your engine’s exhaust system by measuring the proportion of oxygen in the exhaust...

Ilmor Spark Plug Wire Set | PL00224 Ilmor’s spark plug wire set consists of a set of 8 wires, encased in a premium insulating material, connectors, and insulating boots and are the high-quality and trusted replacement for your Ilmor engine. Ilmor...

Long Flexible Funnel For Oil and Transmission Fluid Long Flexible Funnel Fine mesh screen filters out most foreign matter. Non splashing. Lightweight floating polyethylene plastic. Makes putting oil and transmission fluid into hard to reach places a...

Indmar Spark Plug Wire Set | 755007 Get the spark your engine needs with new spark plug wire set. Fits Indmar Ford 351w, 302 (5.8, 5.0) Spark Plug Wire Set, based small blocks with either a Prestolite or a Mallory distributor. Complete set of 9 wires...

Ilmor Raw Water Pump – MV8V‑1072 The Ilmor Raw Water Pump Assembly (MV8V‑1072) is an OEM replacement component engineered for Ilmor’s open-cooled MV8 marine engines (excluding 7.4L models). Designed to deliver consistent sea water flow to...

  This filter is no longer made and sold by MasterCraft. You can purchase the aftermarket replacement filter here -> Fuel Pump Filter for In-Tank Fuel Pumps - MasterCraft

Ilmor Starter Motor The Ilmor starter is the component that gets your engine running, providing ultimate cranking power for reliable and consistent engine starts every time. Use the boat part look up below to ensure you are purchasing the correct part...

Ilmor Knock Sensor w/Bolt | 1015 Ilmor Knock Sensor for MasterCraft boats. Specifically designed by Ilmor and MasterCraft for 5.7L 6.0L 6.2L Ilmor engines.  Made with high-quality materials that ensure OEM specified performance.  Use the boat part...

MasterCraft Ignition Switch Keep your boat starting like new every time with this genuine MasterCraft Ignition Switch with keys. This switch is the replacement part for virtually all MasterCraft boats dating back to 1968. This switch installs easily and...

Indmar/PCM Ford 351 HO 285 HP Spark Plugs Fits all HO Ford 351w engines like 285 HP Indmar 5.8, PCM Pro Boss GT-40, etc. with GT-40 heads. Set of 8. Specs; Plug gap .035".Please note: No returns will be accepted on installed MasterCraft parts. Use the...

1.25" Wire Reinforced Hose This 1.25" wire reinforced hose is commonly found on marine engines and can be used in water or exhaust situations. This hose is reinforced with wire helix imbedded between plies of HD synthetic cord. It is resistant to exhaust...

Prestolite Distributor Rotor (1987 & newer) Fits Ford and GM based V8 engines 1987 and newer with a Prestolite distributor. This is the Rotor only. These engines were used by MasterCraft, Malibu, Supra and Moomba boats. Note: There were a FEW 1987...