Inboard Boat Parts

Prestolite Distributor Cap Fits Ford and GM based V8 engines 1986 and older with a Prestolite distributor. This is a distributor Cap only.Note: There were a FEW 1987 boats built that had the "old" CLIP-ON type distributor cap still.Please note: No...

Brake Caliper for MasterCraft Trailers This replacement Brake Caliper for MasterCraft Trailers is for use on all trailers from 2003-2012. This caliper works for both right and left sides on the trailer and also includes ceramic brake pads. This is a...

Speedometer Pitot Tube Slotted mounting plate allows for easy installation of this competitive Pitot Tube in the existing holes on your boat. This part will replace your broken Air Guide pitot tube that is no longer available. Best of all this Pitot tube...

PTM Edge Elite Mirror The PTM Edge Elite Mirror is the perfect mirror for all of your watersports needs. This mirror provides uninterrupted, high-definition, and high-clarity view of the rider from port to starboard. The PTM Edge Elite Mirror features...

MasterCraft Boats Chrome Decal 20" Whither you are looking to update your old boat or just add a bit of flash to your new boat, the MasterCraft Chromex decal is the perfect fit. Since the Chromex decal comes in three different sizes, it can be used to...

MasterCraft Tower Knob Rear Pivot 2007 through 2011 Genuine MasterCraft tower knob. This knob is designed for 2007, 2008, 2009, 2010 and 2011 MasterCraft boats with a factory Zero Flex Flyer including the X-1, X-2, X-7, X-9, X-15, X-25, X-30, X-35, X-45...

MasterCraft ProStar Glove Box Latch This is a direct replacement MasterCraft ProStar Glove Box Latch for your MasterCraft boat. Keep your MasterCraft boat looking in peak condition with Genuine MasterCraft parts. This latch fits the following MasterCraft...

MasterCraft Boats Wakeboard Tower Knob Genuine MasterCraft tower knob. This knob is designed for 2005 and 2006 MasterCraft boats with a factory tower including the X-1, X-2, X-7, X-9, X-10, X-30 and X-45. This knob is used at the rear foot where the...

Jabsco Green Ballast Impeller Jabsco Replacement Ballast Impeller for use with all Jabsco Ballast Pumps in MasterCraft, Supra, Moomba, and Nautique Boats. Green Ballast impellers are designed for larger ballast systems. They feature a stiffer rubber to...

MasterCraft Ilmor 5.7L Water Temperature Sensor Ilmor Water Temperature Sensor for MasterCraft boats. Specifically designed by Ilmor and MasterCraft for 5.7L Ilmor engines. Ilmor water temperature sensors are engineered for precision and durability...

Propeller Shaft Cotter Pin The Cotter Pin helps ensure that you don't lose your boats propeller and prop nut. Replace the cotter pin every time you change out your boat prop to ensure that you never get stranded on the lake, or worse lose your costly...

MasterCraft Strut for Boats with 1" Drive Shaft The MasterCraft strut is a genuine MasterCraft boat part for boats with a 1" keyed drive shaft. This strut is specifically designed for MasterCraft direct drive boats with a 1:1 transmission. This...

Prop Key 1/4" x 1 1/4" Don't be caught on the lake without a spare Prop Key 1/4" x 1 1/4" This is too important of a piece to be without and let's face it, there is no way to look cool while stranded on the lake. This is a universal part it works on most...

Indmar Knock Sensor Genuine Indmar Knock Sensor. This part is commonly found in Indmar engines in MasterCraft, Malibu, Supra and Moomba boats. This part threads into the block and features a wire harness connector at the other end. Use the boat part look...

Gas Shock 30# Motorbox and Engine Cover Gas strut from MasterCraft Boats used on many MasterCraft boats motorbox and engine covers as well as observers seats. This gas shock is designed to hold up the motorbox cover on your v-drive boat. This gas shock...

Ilmor Ignition Coil Assembly | PV06356 Ilmor Ignition Coil for MasterCraft boats. This is a replacement for Ilmor MV8V-1026. Maintain like-new performance for your Ilmor engine with these Ilmor specified ignition coils. These coils are designed as a...

3M 5200 Marine Adhesive Sealant 3oz Tube 3M 5200 Marine Adhesive and Sealant is used when installing new struts or tracking fins. This high strength and white in color. 5200 provides for watertight bonding and sealing of fiberglass and wood. Ideal for...

Southco Soft Draw Latch This latch is a replacement for your MasterCraft engine box.   Use the boat part look up below to ensure you are purchasing the correct part for your boat.  

MasterCraft 3 Amp Circut Breaker Genuine MasterCraft boats 3 Amp circuit breaker. This marine circuit breaker is ignition protected for use in many marine applications. Features screw top installation with a two prong input. Midwest MasterCraft proudly...

Log Shaft Packing For 1 1/8" Drive Wax impregnated rope for drive shaft and rudder stuffing boxes. Each piece is 3/16 diameter and 4.5" long. The 3/16 shaft packing is designed for boats with a 1 1/8" drive shaft which is commonly found on MasterCraft,...